Reverb lp embed listings12/23/2023 ![]() ![]() For the filter attack, set the filter cutoff to 0, envelope amount to 10, and then set envelope 1’s attack to 17. For the vibrato, raise the LFO fader in the DCO-1 section to 4, and then set the rate in the LFO section to a fast 87. We need to add some vibrato, as well as a quick filter attack, both of which are important parts of the lead synth sound on IGOR’S THEME. To create the synth patch used in IGOR’S THEME’s extended synth solo, use a single sawtooth waveform run through the chorus effect on mode 1 as a starting point. For the sub-bass patch, I used only the sine oscillator, set Sub Tone to 10%, Analog to 50%, turned on Sub Thru, and raised the amp envelope’s sustain to 100%. I used Ableton Live’s Bass synth (from the Max for Live Essentials) set to double the MIDI notes an octave below the PG-8X bass track. The bass in IGOR’S THEME also sounds like it was layered with a sub-bass track, to create a thicker low end. In the VCF section, lower the cutoff frequency to 94 to remove some of the harshness from the high-end, then set the Chorus effect to mode 1 to add some stereo width to the patch. In PG-8X, you set full unison mode by pressing the Mono button in the key mode section at the top of the interface until it’s yellow. You want to put the synth into unison mode, which will set all of it’s voices to double the same note, effectively making the patch monophonic and much thicker sounding. You may need to lower the VCA level to prevent the sound from clipping on the way out of the synth. Set Cross Mod to 3, which sets DCO-2 to be ring-modulated with DCO-1, and then raise the volume of DCO-2 in the mixer section. From the initial setting, set DCO-1’s waveform to the narrow square wave, and set DCO-2’s range to 16’. The patch can easily be created in the free PG-8X software synth, which is a tribute to the JX-8P. The sound no doubt came from Tyler’s Roland JX-8P I tried to create the sound on my Juno but without the cross-mod/ring-mod and the 2nd oscillator, I couldn’t quite get it to sound right. The advanced tab lets you add a CSS class to your block, allowing you to write custom CSS and style the block as you see fit.IGOR’S THEME opens the album with 22 seconds of sustained synth bass to set the tone for the rest of the album. The toggle switch turns blue in the “On” position. “On:” This embed will preserve its aspect ratio when the browser is resized. In the off position, the toggle switch is gray. “Off:” This embed may not preserve its aspect ratio when the browser is resized. The Toggle switch turns on or off the resize functionality for smaller devices. Via the Media Settings, you can control the behavior of your post embed when viewed from a smaller device, like on a phone screen. With the Remove Block option, you can delete the selected block from your content. You can for instance add a common background color or other blocks to the group. Select the Group option if you want to create a group of blocks and treat them as a unit. Using the Add to Reusable blocks option lets you add the selected block to a list of reusable blocks, so you can use them on other posts or pages as well. The Edit as HTML option allows you to modify the HTML code of the embed block. If you select Move To, you will get a blue line inside your content, you can then use the arrows to move that line up and down to where you want the selected content to be moved into, hitting return on your keyboard at that point moves the block to that position. Insert a new block after the selected block(s). Insert a new block before the selected block(s). ![]() The Hide Block Settings option hides (or shows) the Block Setting panel in the editor’s sidebar.Ĭopy can be used to copy a selected block and then you can paste it wherever you want in the editor.ĭuplicate can be used to duplicate selected block.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |